What's wrong with me and my nut plates/screws???

So we all have a bunch of nut plates and screws as provided by Zenith right?

  I have most of mine installed and the screws are hand tightened  - only a few turns until tight right?  So I decide to tighten up an access panel and it's a SERIOUS effort to get any of the screws in tight.  I figure maybe once they are in tight then I can undo them and they will then be smooth going in and out for access panel access right?

 Well, no such luck.  I can barely get them unscrewed and it's still way too hard to screw in and out. Pretty much unusable for an access panel.

 I'm sure I'm not the only one with this problem but I can't find any other threads addressing this.

  I apologize if I'm just missing the prior discussins.

What have you all found? At this point I'm ready to drill them all out and use rivnuts!

Thanks - Jim

Views: 570

▶ Reply to This

Replies to This Discussion

Permalink Reply by John Austin on January 23, 2018 at 1:37pm

Jim,

This is a common problem/complaint.  The nuts are slightly out-of-round so as to provide some thread-locking ability, but I agree - sometimes they are ridiculously tight!

This EAA Video recommends lightly chasing the nutplate threads with a tap to make them a bit less tight.  I don't think I've resorted to that yet, but I usually very lightly grease a screw before using the nut plate the first time.  I think the combo of a little lubrication and the screw slightly expanding the threads does the trick in most cases.  It's not a bad idea to use a "sacrificial" screw on the first attempt so if you slightly tear the slot in the screw, you can toss it and use a fresh screw for the next attempt - usually that will go better with the lube and previous expansion.

John

N750A

Permalink Reply by Lee Engel on January 23, 2018 at 1:44pm

I go though ALL of my nut plates with a tap of the correct size,a little experimenting as I go to get the right "drag" on the screw.    Lee

Permalink Reply by Jim Davis on January 23, 2018 at 10:24pm

You guys are genius!  :-)  A little oil and a little 10-32 tap and I can sleep well tonight.

Thanks a million!!!

- Jim

Permalink Reply by David J. Beaulieu on January 27, 2018 at 9:36am

Jim,  for most of your access panels, or places you would use or like to use nutplates, the smaller sizes will be perfectly fine to use.  The smaller sizes are much easier to screw in and out.  You can use a squeezer to install the associated rivets in most places as well!  The ACS catalog lists all the particular specifics.

Permalink Reply by Jim Davis on January 28, 2018 at 2:35pm

Thanks :-)

Permalink Reply by Joe Spencer on January 28, 2018 at 7:04pm

I run a tap thru every one of em

RSS

New from Zenith:

Zenith Planes For Sale 
  

Classified listing for buying or selling your Zenith building or flying related stuff...

Custom Instrument Panels
for your Zenith:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, Dynon and Garmin avionics, and more.

Zenith Homecoming Tee:

Zenair Floats

Flying On Your Own Wings:
 A Complete Guide to Understanding Light Airplane Design, by Chris Heintz

Builder & Pilot Supplies:

Aircraft Insurance:

 
 

West Coast USA:

 
Pro Builder Assistance:

 

Transition training:

Lavion Aero

K&S Aviation Services

Aircraft Spruce & Specialty for all your building and pilot supplies!

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

© 2024   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service