Replies to This Discussion

Permalink Reply by Keith Thomas on May 7, 2020 at 1:10pm

Have you ever got this working?

• ▶ Reply

Permalink Reply by Fred Williams on May 8, 2020 at 10:14am

Love it.  Gotta have it.  Will save you and your forearms.  The tips that I received from Zenith with the concave heads did fit the tool.  I understand Zenith will also take a set that you send to them and grind/turn the appropriate shape into the head.  I bought one late into my build.  Works great.  

• ▶ Reply

Permalink Reply by Keith Doot on May 8, 2020 at 11:18am

Fred;

Thanks for the information.

I have some M12 Milwaukee tools. Good to know the Zenith heads fit.

I will add it to my collection since I won't have to worry about compressed air for a rivet setter.

Thanks again;

Keith

• ▶ Reply

Permalink Reply by Stephen Bradley on May 9, 2020 at 4:19pm

I use this gun and it’s awesome!
You can’t modify the Milwaukee nose piece as there is a cavity below the surface that holds a ball bearing (that grips the rivet and stops it falling out)

It took me a while but I found a nose piece from a long arm rivet gun that fit. And I shaped those and it works great.

It’s possible that an air rivet gun nose piece may fit?

• ▶ Reply

Permalink Reply by Mike Chapman on May 9, 2020 at 10:43pm

I bought the Milwaukee Rivet Gun before starting my build...I'm way more than pleased with it.  I did have a bit of a learning curve...there is a small ball bearing secured in each nose piece with an O-ring.  That ball bearing puts pressure on the rivet stem to prevent the rivet from falling out of the nose piece; however, when the rivet is pulled, the rivet stem stays in the barrel/neck of the rivet gun.  When I would insert another rivet, sometimes the stem of the newly inserted rivet would jam against the previously captured rivet stem.  I would have to take the barrel/neck off the gun and remove the jam...not difficult, but frustrating.  The solution was to remove the o-ring and ball bearing...after doing that, the rivet gun has been trouble free pulling thousands of rivets:

A pneumatic rivet puller is a bit faster...but, as far as I'm concerned, not having to listen to a compressor cycling on and off...and not having to drag an air hose around my work area far outweighs the minor decrease in pull speed.

I machined the Milwaukee nose pieces using an SE-5 Carbide Bur.  I didn't have any issue with the nose pieces being too hard to machine...the carbide bur cut the material without any problem.

The nose pieces for the manual rivet puller in the picture (DeWalt Swivel Head) are NOT interchangeable with the Milwaukee M12 rivet gun.

• ▶ Reply

Permalink Reply by Keith Thomas on May 10, 2020 at 11:44am

Thanks I guess Ill try to machine my puller heads, i have spares on order.

• ▶ Reply

Permalink Reply by John Austin on May 10, 2020 at 7:28am

Question:  Does the M12 pull rivets slightly slower or "more gently" than a pneumatic rivet gun?

The reason I ask, is that I have the typical pneumatic rivet gun that Zenith sells.  It worked great, but one day I was riveting a piece of aluminum that had been powder coated.  The rivet holes were drilled after the powder coat process, so of course that broke the seal of the powder coat.  When I started to pull rivets with the pneumatic gun, I noticed a ring of blistered-up powder coat around each pulled rivet!  My theory is that the pneumatic gun pulls the rivets so quickly, it creates a tiny blast of compressed air around the rivet head as the "domed" or rounded head is formed.  This tries to escape through the broken seal of the powder coat, lifting up the powder coat.

Of course, the obvious solution for me was to pull the remaining rivets with a manual rivet puller and I had no further problems.  Just wondered if the pulling action is a little slower or more deliberate on the M12? This might also prevent some of the little "smilies"/dents/dings that can result if the pneumatic puller recoils and bounces off the surface around the rivet.

John

N750A

• ▶ Reply

Permalink Reply by Mike Chapman on May 10, 2020 at 12:06pm

With the Milwaukee riveter, it's a steady and strong pull.  I guess you could say it's BOTH slower and more deliberate.  There is still some recoil as the rivet stem breaks; however, I find it much easier to control than the quicker pop and recoil of a pneumatic gun.

• ▶ Reply

Permalink Reply by Kyle Hutchings on October 13, 2022 at 3:52pm

A little late to the thread, but in case anyone is looking for Milwaukee nose pieces that do not have the retention cavity I discovered these replacement pieces after finding out the hard way the retention noses should not be machined.  I have not ordered or tried them out, but they appear to not have the retention cavity so there shouldn't be any issues machining them.  Here are the part #'s, I was able to find them on greatlakespowertools.com.

48-98-0005 --> 3/32"

48-98-0010 --> 1/8"

48-98-0015 --> 5/32"

48-98-0020 --> 3/16"

• ▶ Reply