Prewired R/R connector from UL

To repair my "crispy" wires from the PMA to the R/R connector I ordered a prewired connector from the UL distributor (Wicks Aircraft).  Keith is very helpful and is starting to have good inventory of parts on hand.  Upon receipt, I noted that the wire size for the output pos and neg leads to the aircraft seemed to be undersized for a 30A load.  The wire size are 12ga and I'm thinking they should be 10ga . In the latest install manual the wiring diagram shows those wires as an 8ga to gnd and 10ga to the aircraft system.

For those running a 350iS what are typical amp draws during high power cruise flight conditions?  I have a dual ECU setup and draw approx 20A while cruising at 2600 rpm with all equipment functioning except pitot heat.  With the Dynon pitot heater on and cycling I draw an additional 8 amps.  When initially (after takeoff) topping off the batteries due to ground (non-flight use) I suspect that I am maxing out the capacity of the alternator for a while and have at least 30A going thru the 12ga output wires.  

The prewired connector consists of the three phase wires with 1/4" crimped female spade terminals, and two output wires with 5/16" crimped female spade terminals.  I am considering removing the output wires, and replacing with 10ga and new crimped terminals.  In the meantime, Ray Lawrence is going to ask UL in Belgium their thoughts and if those do need to be 10ga wires.

Any thoughts or questions regarding this anybody?

Cheers!  Dave

Views: 718

▶ Reply to This

Replies to This Discussion

Permalink Reply by Gary Welch on January 5, 2019 at 6:05pm

My cursory review suggests you are right to be concerned. You may want to review Bob Nuckolls white paper on wire sizing here:

http://www.aeroelectric.com/articles/wiresize.pdf

The length of the wire, continuous/intermittent duty and the temperature of the wire are all related.

It's certainly true that many builders unnecessarily over-size wires. The only penalty for this is weight and possibly and difficulty in fab'ing terminals.

On the larger wires, with longer runs, the added weight of over-sizing can be significant. I had considered putting the battery in the rear fuse until I calculated the added weight of the cables was just over 7 lbs! Decided that a 4.1 lb EarthEx battery towards the front of the plane made a lot more sense.

Permalink Reply by Tom Sullivan on January 5, 2019 at 9:55pm
Yeah my thoughts exactly David. I actually thought the output wires were 14 ga. but I think 12 is more accurate. I wondered why they were so light while the diagram shows 8 and 10 ga. wires. Not going to address this just yet as I have a ways to go but I will watch it.On engine runs I draw 17 to 20 amps depending on batt state of charge.Thanks for the good info.
Permalink Reply by David J. Beaulieu on January 6, 2019 at 10:57am

Tom, thanks for the amp draw info.  That seems a bit high when comparing to the UL charts for ECU and fuel pump electric load.  Was that with the battery fully charged?  Any other equipment drawing amps?

I plan on replacing the output wires from the prewired connector as soon as I can locate an appropriate pair of crimpers for the terminals and 10 ga wire size.

Permalink Reply by Tom Sullivan on January 6, 2019 at 9:24pm

I think it was charging the battery at that time with the Skyview.ECU and pump. The only other draw is the lights which might be an amp.

Permalink Reply by Jerold Ebke on January 8, 2019 at 10:40pm

Hello fellow UL flyers,

This response is for both recent posts about this issue.

I had 2 similar experiences with the connector on my 350i when I had the Reg/Rectifier mounted on a thin aluminum sheet on the motor mount  with the blast air tube from the cylinder cooling box.

I duplicated the design from the firewall forward install instructions.

After failure #1, I made sure the electrical connector was absolutely tight to reduce any chance of heating due to arcing, resistance from incomplete engagement etc. at the plug.

After the 2nd episode, I moved the Reg/Rectifier to the firewall and placed some heat transfer paste between the two. The volume of metal in the firewall is able to dissipate a lager amount of heat.

Since then, I have had absolutely no change in the wires or connector and I am up to 320 hours.

This may be luck, coincidence or actual.

I believe the heat discharged by the Reg/Rectifier was more than could be dissipated by the air blast and the thin aluminum mounting plate. As the heat increased in the R/R, the plastic connector and wire insulation suffered and eventually failed.

I cannot explain why some installs have no troubles and others have.

This is purely my opinion and based only on my experience.

Best luck to my fellow builders.

Jerry

Permalink Reply by John Bell on October 29, 2019 at 4:37pm

Hey Tom.

What diagram shows the RR leads as 10 awg? Rev 13 pf the manual still shows 12 awg to the battery but I plan on upsizing them to 10 anyway.

John

Permalink Reply by David J. Beaulieu on January 9, 2019 at 6:48am
Thanks for posting Jerold!! Do you happen to know what your typical electrical load is during flght? Cheers! Dave
Permalink Reply by Jerold Ebke on January 11, 2019 at 9:55am

David,

I have LED lights and one screen full Skyview Classic system along with standard UL firewall forward (fuel pumps etc ).

If the sensor can  be believed, my amp reading during cruise flight is 18 amps at 2500 RPM.

Jerry

Permalink Reply by John Bell on October 28, 2019 at 5:39pm

Hey David. Did you end up changing the leads to 10 awg? After discussions with Ray,  I Decided to go with a 40 amp ANL fuse between the regulator and battery. This is a disaster scenario fuse designed soley to protect the battery and master bus during a what if failure in the regulator/alternator. I do not have a fuse between the battery and master bus as noted in the UL drawings.
I too think the 12awg leads are to close to the edge here.

John

Permalink Reply by David J. Beaulieu on October 28, 2019 at 7:31pm

Hi John, yes I did!  I used the UL prewired connector and upsized the ground and output wires to 10 ga wire via soldering to terminals which I then inserted to the plastic connector.  At the same time I also replaced the R/R and applied fresh heat paste on the backside. Over 50 hours on that mod and everything looks good so far.

Permalink Reply by John Bell on October 28, 2019 at 8:08pm

Thanks David.

Mine came with the prewire plug already in the regulator. That connector is really tight. I have been reluctant to pull it out but may give it a try tomorrow. Standard spade connectors I suppose?

Permalink Reply by David J. Beaulieu on October 28, 2019 at 8:19pm

I seem to recall most distinctly that I needed 5/16 for those two versus 1/4...NOT 100% positive though...

RSS

New from Zenith:

Zenith Planes For Sale 
  

Classified listing for buying or selling your Zenith building or flying related stuff...

Custom Instrument Panels
for your Zenith:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, Dynon and Garmin avionics, and more.

Zenith Homecoming Tee:

Zenair Floats

Flying On Your Own Wings:
 A Complete Guide to Understanding Light Airplane Design, by Chris Heintz

Builder & Pilot Supplies:

Aircraft Insurance:

 
 

West Coast USA:

 
Pro Builder Assistance:

 

Transition training:

Lavion Aero

K&S Aviation Services

Aircraft Spruce & Specialty for all your building and pilot supplies!

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

© 2024   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service