I plan to start building a 601XL this Winter and want to put a 0-200 in it. I did transition training with Buzzy earlier this year and his 0-200 in the 750 seemed to perform well.  I’ve been looking at several options

and one is that I have the opportunity to buy a good running 150 with 700 hours smoh, know the pilot,

his mechanic and how the plane has been cared for.  He wants 12,500. for it and it’s sitting in a hanger

close to me.  Realizing I wouldn’t get much for the airframe, besides the engine/prop - there are a few things on the instrument panel and the elt that I could use.  My UL350is and prop was more than twice that. Is this a dumb idea.

Views: 541

Reply to This

Replies to This Discussion

Hi, Robert;  How *well* do you know the pilot? As in, you've seen him/her around, or you've sat and talked, perhaps flown with them, etc.

Are you sure about the 750 SMOH or STOH?  Have you read the logs?

If you *really* know this plane, the owner, and really understand how it's been maintained, I don't think it's a bad deal.

You might have to still put some $$$ into it; as an example, some mags need to be o/hauled on a regular basis. You might have a weak cylinder or two. You might want to put a lightweight starter and/or alternator on it. o-200's did not come with an oil filter as standard equipment. I would seriously consider adding one if the previous owner(s) haven't done it already.

Has current owner done oil analysis?  If so, review the last few reports just to check trending data.

Plan for an extra 2-3000 $ just so you're not surprised.

Hi Carl,  Thanks for replying. Yes, l know the pilot well - we have shared a hanger for

the last 14 years.  He has been meticulous about taking care of it, just doesn’t fly it much,

though it’s always in annual.  He might not appreciate it if I told him what I would do with

it and I wouldn’t do it without telling him before I bought it.  I just thought getting a running

engine might be a lot easier.

  I can buy a complete engine from a friend for 2500 bucks, which has been sitting in his

hanger for probably 15 years.  It is very low houred, turns free, but had a prop strike and

besides a crank check may also need new cylinders as well as mags, light wt. starter, etc.

He will let me tear it down and check it before I buy it, so I suppose that’s a better way

to go.  Did you start with a core?

Thanks,

Robert

Hi, Robert;  It all depends on how you want to go. For me, building an engine is viewed as "fun" but I have an engine background.

Depending on how far your friend will let you tear-down the 2500$ engine, and if you enjoy building, go for it. I bought a core for $4000 or thereabouts, and I'm planning on about $14,000 total when I'm done. I've already had the internals tested & tagged, as well as the case.  I need a new accessory case, so that will be a big chunk.  Cylinders all had good compression, but I'm going with new Superiors; more to be able to go back to 28 deg of timing vs 24 as limited by the older cylinders.  Starter is less than 100 hrs old, so it pains me to go with a new one; will probably go with a new one anyway.  One slick mag is also at 100 hrs, so will need another mag. Carb was just overhauled.

Christopher below makes some good points, but for an experimental, the 12 years / 1800 hrs is only guidance. More important to me is how regularly (the one in the 150) it's been flown. I'd rather have a 50 hr/year engine that's flown every week than one where it sits for months or a year, then has 150 hrs put on it the next year. Supposedly you know the history on its use. Does either engine have the mounting pad for an engine-driven fuel pump? The 150 probably doesn't since it's a high wing. The other one in your friends shop may/may not. Since you're a low-wing you'll need to determine that impact as well.

If you have the time to part-out the 150, you can't ignore the possibility of going with a -D.

The recommended OH time doesn't apply because of Part 91 not for hire operations, not if experimental or certificated. But once again beware of old,  slightly used engines unless aware of the effects of sitting in an unpreserved state (as most are)

The problem Id worry about is the overhaul "timing" out, 12 years between OH or the TBO of 1800. If you are willing to fly behind an old one, You would make out by selling the 150 in parts or airframe project.

The cylinders and lifters will likely show corrosion from lack of use. Seals and magneto componets also degrade with time (drying out or becoming brittle.


new O-200D better than the O-200A and about 24K. Overhauling the O-200A with monies gained in selling C-150 stuff is possible.


Only negative of the D, or the A model from C-150 ...No engine driven fuel pump.


I am an A%P and sold my timed out 150 and used cash to pay for new O-200D. Lighter and much more power, as well as mental security wondering about the old motor fatiguing out plus how my OH's on the C-150 motor, probably not its first time around

Thanks to both of you.  You have helped me decide to back off and give it all lots

more thought.  While I still work on engines, I am 69 and it’s not as much “fun” as

it once was - upon returning from Vietnam a friend and I had a shop and built &

rebuilt engines - mostly auto, diesel & motorcycle and also his Dad had a small

machine shop so we did all our own head work and bored a few engines. I have

really never worked on my airplanes because have always had a partner and the

liability wasn’t worth it.

  Anyway, being mostly retired, I built my 750 last Winter, learned a lot and had

a great  time. The reason for building the 601 is to keep busy and I plan to take

my time, have a pro painter paint it, and try to build a plane someone will be proud

to own. I painted my 750 and it’s very average.  I also think it’s even more important

to build the plane with a trusted and proven engine when selling it to someone

and I plan to sell it.

  That all being said, I probably won’t break even on it so I need to keep an eye on

that part of it.  Thanks to both of you, I needed to hear what you had to say!

RSS

New from Zenith:

Zenith Planes For Sale 
 

Classified listing for buying or selling your Zenith building or flying related stuff...


Custom Instrument Panels
for your Zenith
:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, Dynon and Garmin avionics, and more.


Zenith Homecoming Tee:


Zenair Floats


Flying On Your Own Wings:
A Complete Guide to Understanding Light Airplane Design, by Chris Heintz


Builder & Pilot Supplies:

Aircraft Insurance:

 
 

West Coast USA:

 
Pro Builder Assistance:

 

Transition training:

Lavion Aero

K&S Aviation Services

Aircraft Spruce & Specialty for all your building and pilot supplies!

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

© 2024   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service