• Male
  • Birdsboro, PA
  • United States
Share on Facebook
  • Blog Posts
  • Discussions (10)
  • Events
  • Groups
  • Photos
  • Photo Albums
  • Videos


  • Thomas L. Cline
  • nelson D
  • Joseph F. Truncale
  • John Rizzo
  • Mike Ethridge


Profile Information

Aircraft Model
Project Status
Building From
Engine installed (or plan to install)
Rotax 912
Building Experience
No Experience
Flying Experience
Private Pilot
Building and Flying Info / Your Profession / Other Background Info

Comment Wall (13 comments)

You need to be a member of Zenith Aircraft Builders and Flyers to add comments!

Join Zenith Aircraft Builders and Flyers

At 1:14pm on March 27, 2013, Bob McDonald said…

Ken the graphics were done by

Contacts name was Ashley Martin.

Kitchener, Ontario, Canada

At 5:08pm on June 10, 2012, Bill Alexander said…


I used AN hose fittings that were bought from JEGS. The race car people use a lot of AN fittings of all sizes and configurations. If you look on line you can find most anything you may need.


At 8:38pm on April 8, 2012, Dr. Edward L. Olds III said…


Glad to hear that you are  happy with the Aerotronics folks.  I am not installing an autopilot right now, but may in the future.  I just did an approach to minimums in a twin (I was right seat) while bringing my aunt home and it was done by the autopilot!  I was sold.


At 10:42pm on March 8, 2012, Dr. Edward L. Olds III said…


Finally home from my trip to help with my aunt.  I can say nothing but the best things about Aerotronics.  They were great to deal with and Jason Smith, who handles most of the experimental stuff was a real help in planning and design.  He gave me lots of ideas to make the panel cheaper, but even better.  Now remember, "cheaper" is a relative term.  My cost was @ $18,000, but when I compared what I was getting with just buying the equipment and trying to do it all myself, I thought it was very fair.  I only have about 9 wires to connect and some antennas to install and the AHARS to mount and I can run the system.  Dynon makes upgrades easy, too.


At 11:04am on March 4, 2012, Dr. Edward L. Olds III said…
I'm dealing with an elderly aunt in the hospital and can't get to my computer, so I will say more later. Aerotronics is super, not cheap, but are wonderful.
At 2:15pm on February 8, 2012, Bill Alexander said…


In answer to your guestions. Yes the stiffener is hollow, the drill bit just cleans out a clean hole so the rod will slip in easily. I used  steel rod on the rear because that what was laying around the shop, I think I used about 8 oz of epoxy, Then I decided to do the front and bought some aluminum rod, this time I used some very good construction adhesive, found at Lowes, its cheaper and more of it. You can drill some 1/16 holes down the stiffener, to see epoxy  oozing  out and let you know you have it down there. taper the end  of the rod,so it wont push all the epoxy out in front of the rod as you push it in. I think one more important thing is to change the location of the hole in the bottom latch for the rear latch pin to give it more travel. This will insure the rear of the door will stay latched.I also added a bracket under the gas strut attachment point to spread the load on the door frame. Too date very happy with the mods, the door is much more ridged, I do not think it will fail again.


At 1:37pm on February 8, 2012, Mike Ethridge said…

Ken I have been out of the country but will make a point of part numbers etc on Friday.


At 8:34pm on January 10, 2012, Mike Ethridge said…

Its the only way to go and will take and send pictures next week. mike

At 2:14pm on August 22, 2011, John Weigel said…
Still waiting for the new rails to arrive.
At 8:13am on August 6, 2011, John Weigel said…

I did not end up using those rails.  I'm really liking the ones in this thread.



New from Zenith:

Zenith Planes For Sale 

Classified listing for buying or selling your Zenith building or flying related stuff...

Custom Instrument Panels
for your Zenith

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, Dynon and Garmin avionics, and more.

Custom Upholstery Kits for your Zenith Aircraft:

Zenith Vinyl Upholstery Kits

Zenith Homecoming Tshirt:

Zenair Floats

Flying On Your Own Wings:
A Complete Guide to Understanding Light Airplane Design, by Chris Heintz

Builder & Pilot Supplies:

How to videos from

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit for the latest DVD titles.

Aircraft Insurance:


West Coast USA:

Pro Builder Assistance:


Transition training:

Lavion Aero

K&S Aviation Services

Aircraft Spruce & Specialty for all your building and pilot supplies!

© 2023   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service