Jabiru Gen 4 manifold pressure?

Hi.  I am trying to figure out the wiring for the Dynon sensors on my Gen 4 Jabiru 3300.  I am not familiar with the engine, I have always had Lycoming or Continental.

I have been trying to figure out where to plumb the Dynon MAP (manifold air pressure) sensor and which wires from the EMS Dynon wants me to use.  In slogging through Dynons 500+ page manual, they call out map sensor wires from the EMS for Continental, Lycoming, Rotax, but not for the Jabiru 3300.  Are there no map sensor options for the Jabiru?  Where on the motor do you pick up the vacuum?

My engine manual states I have a “not a Bing” carb, but it doesn’t say what make the new carb is.  I am not sure if the barb coming out the bottom of the carb is for a map sensor, or if it’s just an overflow…

Has anyone used a map sensor with the Jabiru/Dynon combo?

thanks

Views: 168

▶ Reply to This

Replies to This Discussion

Permalink Reply by John Burns on November 15, 2023 at 7:35pm

Typically that barb on the carburetor connects back to the air box as a balance pressure to adjust the carburetor for changes in altitude.  If you have not found it yet the Jabiru engine installation manuals are here Jabiru Manuals

Permalink Reply by Fred Wellman on November 15, 2023 at 8:15pm

Thanks, but on my “ not a bing” carb the balance tube is built into a (what appears to be 3D printed) piece “Cobra Head” that goes to the intake.  I am talking about  a barb that comes out of the bottom of the carb in the back.

In the attached photo the balance tube, I believe, is the blue hose.  The barb I’m talking about is barely visible in the lower left corner. It comes out downward, out of the left side of the carb.  None of the carb pictures in the manual shows it.  It might just be an overflow, but I’m not sure.  There is no info on it.

At any rate, I’m still trying to figure out where to connect the vacuum tube for the Dynon map sensor…

Thanks

Attachments:
Permalink Reply by John Burns on November 15, 2023 at 8:25pm

John Austin can help with the link, but the Jabiru online community has said that the new carburetor is a Mikuni PD42J carb  if that helps, not certain if this is correct, but it might help you find some more information about the carburetor.  I did not install a manifold pressure gauge, but I have MGL avionics and I opted not to get the MAP option. 

Permalink Reply by Fred Wellman on November 16, 2023 at 7:42am

Thanks John. I'll see what I can dig up on that carb.

Fred

Permalink Reply by Dave Geiling on November 16, 2023 at 5:14am

Fred, I currently have one of the new not-a-bing carbs on my gen 1 engine.  I had previously installed a manifold vacuum gage on the original bing and my recollection is that I was able to use the same plumbing setup.  Which was to use the plugged port that leads to a small hole in the carburetor throat just downstream of the throttle plate.  I don't have an photos, but the port is or is very close to the brass tube shown in the picture.  Sorry this description is somewhat vague, but it was a while ago.  I'll be at the hanger later today and will get a photo.

Dave G

Permalink Reply by Fred Wellman on November 16, 2023 at 7:43am

Dave,

Thanks, I appreciate that.  I will take a look at my carb. A picture of your setup would be super helpful!

Fred

Permalink Reply by Dave Geiling on November 16, 2023 at 4:37pm

Hey Fred, here are a couple pictures of my manifold vacuum gauge connection.  You are correct about the proper connection point being the brass barbed fitting in front of the float bowl.  I used an automotive fuel hose to adapt from the barbed fitting to an AN fitting on a teflon stainless steel braided hose going on to the gauge.  Hope this helps.

Dave G

Attachments:
Permalink Reply by Fred Wellman on November 16, 2023 at 6:40pm

Thanks for the pictures. Worth a thousand words.  I thought that might be it, but I wasn't sure. I appreciate the help.

Fred

RSS

New from Zenith:

Zenith Planes For Sale 
  

Classified listing for buying or selling your Zenith building or flying related stuff...

Custom Instrument Panels
for your Zenith:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, Dynon and Garmin avionics, and more.

Zenith Homecoming Tee:

Zenair Floats

Flying On Your Own Wings:
 A Complete Guide to Understanding Light Airplane Design, by Chris Heintz

Builder & Pilot Supplies:

Aircraft Insurance:

 
 

West Coast USA:

 
Pro Builder Assistance:

 

Transition training:

Lavion Aero

K&S Aviation Services

Aircraft Spruce & Specialty for all your building and pilot supplies!

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

© 2024   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service