zihad mahmud
  • Penang
  • Malaysia
Share on Facebook

Zihad mahmud's Friends

  • Albert Tan Ken Guan
  • KAU AERO TEAM
  • zo flyer
  • Dan Sherburn
  • Conrad Watters
  • martin acton
  • Joe McGough
  • Paul Sanders
  • Paul Saccani
  • ADAM LEE
  • Jim Derickson
  • Adel Alyahya
  • Peter Thomson
  • Chumphol Sirinavin
  • Bruce Cobo

zihad mahmud's Discussions

Piloting equipments

Started this discussion. Last reply by François Balaux Apr 1, 2014. 5 Replies

Salam and hi guys,I am a builder of CH750 in Malaysia. We are now in progress building the fuselage and cant wait to get the aircraft stand on its gear.In the mean time, i am preparing a list of…Continue

 

zihad mahmud's Page

Profile Information

Aircraft Model
STOL CH 750
Project Status
Less than half
Building From
Kit
Engine installed (or plan to install)
Continental O-200
Your website (about your aircraft...)
http://aerospace.eng.usm/CH750
Building Experience
No Experience
Flying Experience
None
Building and Flying Info / Your Profession / Other Background Info
aerospace engineer grads 2007. Currently working on assembling CH750 kit and a certified kit builder for CH750 from Department of Civil Aviation (MALAYSIA) for airframe.
Home Airport (ie. KMYJ)
WMKP

zihad mahmud's Photos

  • Add Photos
  • View All

Comment Wall (7 comments)

You need to be a member of Zenith Aircraft Builders and Flyers to add comments!

Join Zenith Aircraft Builders and Flyers

At 7:30am on January 10, 2014, Jim Derickson said…

Hi Zihad, I did drill out the cover to tighten the bolt.  1" dia. and used a metal hole plug found at the local hardware store. Used in electrical boxes. You can remove it if you need access later. Hope this helps, Jim

At 4:56am on April 18, 2012, Paul Saccani said…

> Oh, you knew capt siva?

Mainly by reputation, though I'm sure I we must have meet a few times at TUDM Simpang during the Rakun Muda aeronautical program.

He pretty much started Expermental aviation in Malaysia, and got the approvals to allow it to start.

>  Yes, this ch750 building is sponsored by our university through research grant.

What is the USM trying to achieve here?  Will it be a one off, or is it hoped to continue the program?

> I am just assisting the leader of the grant to build the airframe. so, we are building it part time, as you know, we have to do other works such as labs and admins stuff. We are also assisted by our students to build the airframe.

What do you plan to do with it when you finish it?  Have you talked to Percy (If I recall his name correctly) down at Penang Aero Club?
Will you do your test program at Bayen Lepas?  You might find the airfield at Taiping, Perak to be suitably quite, instead of operating from Penang International.

>  about the crashed of 9M-EEL, i havent heard about it crashing to a pole. capt siva only told me that the a/c is blown away by a gust from a sikorsky that resulting and upside down of the a/c. but the pilot is fine and still the a/c is still flying now.

I hadn't heard about that crash.  The one that I know about was on 15 july 2006.  You can see some pictures here http://s47.photobucket.com/albums/f198/asmara_kawaii/9M%20-%20EEL/ , with EEL looking very sad indeed, yet dignified.  On board were Lee Chong Yen (Builder) and Atan Akmar Masbah.  The way I recall it, there was an engine failure in the circuit, and as they tried a glide approach they struck a light pole on Federal Highway One, Sungei Besi.  However, my memory may be in error, when I look it up, everyone talks about a gust of wind blowing it into the light pole.  Having said that, the gust of wind explanation doesn't make a lot of sense to me.  You should not be in a position where a gust of wind can blow you into a light pole!


>  how about you paul? did you buy the kit by yourself?

Mixture of plans built and kit parts, a lot of the harder stuff, like welded assemblies (except the engine mount), main undercarriage and the solid riveted stuff was from Zenair.

It has been 99% complete for two years, but now it is 95% complete!

I'm making a few changes, and I've had to replace some calander lifed components.  Due to CG issues, my engine is very close to the firewall, so I can't change my nose bungee without pulling the engine, and as it is ten years old, I do want to replace it before first flight.  And seeing as the I had easy access to the nose gear, I've been re-engineering it to have a lower bearing similar to the one you have in the 750, though made of Teflon instead of nylon 6,6.  Not that I have anything against using Nylon, it was just easier for me to get some Teflon.

As you may or may not know, the lower bearing in the 750 nose gear acts to centralise the rudder in flight, whilst the steering connections for the rudder pedals to the nose gear act to tension the rudder cables.  Many people complain of excessive stiffness in the 701 version, which uses two shaped pieces of aluminium in that role.  Your 750 uses a single large piece of nylon to do the same job, whilst mine will use a large lump of Teflon, which should be slipperier - at the expense of being somewhat heavier than Nylon.

 

Regards,

Paul

At 2:53am on April 16, 2012, Paul Saccani said…

Oops! Apologies for the typo on your name, Zihad.

At 2:52am on April 16, 2012, Paul Saccani said…

G'day Zinhad,

Nice to see your progress.  Did KPT Siva tell you about the crash history of 9M-EEL?

There is no better testimony to the ruggedness of the design than the lack of injuries received after it hit a light pole and lost a wing near TUDM Simpang after an engine failure.  And to be able to be repaired to the marvellous rebuild that you have flown in.

Is your aircraft USM sponsored?

Regards,

Paul Saccani

At 7:35pm on August 13, 2011, Adel Alyahya said…

Hello Zihad

I

 use for anti corrosion ( Cortec) that supplied with the kit and Where I live in the desert (Riyadh) I think it is more than enough .

For painting I have chosen auto primer it is called Sikken which come in gray or paige color. at first we cleaned the surface with lacquer thinner and sanded it with sand paper no. 400 then sprayed the primer for future applications. I think there are many other ways to paint , and if you ask people who are more expert than me they will help you better .

 

BTW, what is the engine you are going to use for the kit , ?

 

Wish you good luck

 

Adel y

At 1:36am on July 17, 2011, martin acton said…

Hello Zihad, just seen your message. What can I try help you with?

regards Martin

At 9:13pm on June 7, 2011, Danny Creech said…

Hi Zihad, If you need help finishing the aircraft or training, I can come help you. I live in the USA but love going all over the world helping builders. I have built three Zenith CH-701s and I am an FAA Gold Seal and Master Flight Instructor. I also hold an Airline Transport License both here in the USA and in The Philippines.

Captain Danny Creech

 
 
 

New from Zenith:

Zenith Planes For Sale 
 

Classified listing for buying or selling your Zenith building or flying related stuff...


Custom Instrument Panels
for your Zenith
:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, Dynon and Garmin avionics, and more.


Zenith Homecoming Tee:


Zenair Floats


Flying On Your Own Wings:
A Complete Guide to Understanding Light Airplane Design, by Chris Heintz


Builder & Pilot Supplies:

Aircraft Insurance:

 
 

West Coast USA:

 
Pro Builder Assistance:

 

Transition training:

Lavion Aero

K&S Aviation Services

Aircraft Spruce & Specialty for all your building and pilot supplies!

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.