Charles Clayton
  • Male
  • Mastic, NY
  • United States
Share on Facebook

Charles Clayton's Friends

  • Jeremy Lauer
  • Raffaele Signorile
  • David Banahan
  • Damien Graham
  • Stan Cooper

Charles Clayton's Discussions

Hard starting Rotax 912 ULS

Started this discussion. Last reply by Charles Clayton Jun 14, 2023. 8 Replies

So it started in January. I was having an unusually hard time starting my 912. The first time I killed the battery and had to jump start it. But then it ran fine for a flight. I thought it might have…Continue

Charging issue

Started this discussion. Last reply by Charles Clayton Jun 12, 2019. 3 Replies

So about 2 weeks ago I was flying along and started having an intermittent low volt light come on with a drop in the voltage to just above 12. It would last a few minutes then go back to normal. I…Continue

First trip in the Hudson River VFR Corridor

Started this discussion. Last reply by Charles Clayton Feb 23, 2017. 6 Replies

To make a long story short I bought my 601XLB to take lessons for my sport pilot license. I got that the beginning of last December. My instructor and I didn't do the airspace training or any flight…Continue

 

Charles Clayton's Page

Latest Activity

Charles Clayton posted a discussion

Hard starting Rotax 912 ULS

So it started in January. I was having an unusually hard time starting my 912. The first time I killed the battery and had to jump start it. But then it ran fine for a flight. I thought it might have been because it sat for 5 weeks(tied down outside). So I figure I need to fly it more often. Next time out a week later, still hard start but I did not kill the battery. Again it ran fine. Went out about a week later, too windy to fly so I decided to just run it(apparently not a good idea). Again…See More
Mar 26, 2023
8 Comments
Evan Reisman left a comment for Charles Clayton
"Hi Charlie, Thanks for getting back to me. I spoke with tech support at Matco and I think the holes align close enough that I will be able to drill them a bit larger and things will fit. I'm purchasing an adjustable hand reamer that can open…"
Oct 27, 2021
Evan Reisman left a comment for Charles Clayton
"Hi Charlie, My name is Evan Reisman and I saw your post regarding replacing your Mark Ingegno wheels. I have the same exact situation as you did. I brought the Matco Wheels. I went on the word of Roger but haven’t yet removed the current…"
Oct 26, 2021
Charles Clayton posted a discussion

Charging issue

So about 2 weeks ago I was flying along and started having an intermittent low volt light come on with a drop in the voltage to just above 12. It would last a few minutes then go back to normal. I did research and it appears that this could be an issue with the voltage regulator. I have the older model Ducati voltage regular. I checked the connections to it and did not see any corrosion. In my testing since when I first start the engine everything works normally for about 5 minutes. Then I hear…See More
May 29, 2019
3 Comments

Profile Information

Aircraft Model
ZODIAC CH 601
Project Status
Flying
Building From
Purchased finished aircraft
Engine installed (or plan to install)
Rotax 912
Building Experience
No Experience
Flying Experience
Sport Pilot (or Ultralight)
Home Airport (ie. KMYJ)
KHWV

Charles Clayton's Photos

  • Add Photos
  • View All

Comment Wall (2 comments)

You need to be a member of Zenith Aircraft Builders and Flyers to add comments!

Join Zenith Aircraft Builders and Flyers

At 10:06pm on October 27, 2021, Evan Reisman said…

Hi Charlie,

Thanks for getting back to me. I spoke with tech support at Matco and I think the holes align close enough that I will be able to drill them a bit larger and things will fit. I'm purchasing an adjustable hand reamer that can open the holes ever so slightly so that the new axle will match up with the holes. I'll post some pictures if I can make this work. I noticed from the pictures you posted that your mechanic took the old Ingegno axle and modified it to work. That seems like an ingenious solution. I also asked the Matco tech person if I could buy un-drilled axles and then use the old axle as a template and drill them myself. He told me that they make the axles in batches and I may have to wait up to 6 months for the next batch, so I'm going to try my first idea of making the holes slightly bigger.

Thanks again!

Evan

At 7:06am on October 26, 2021, Evan Reisman said…

Hi Charlie,

My name is Evan Reisman and I saw your post regarding replacing your Mark Ingegno wheels. I have the same exact situation as you did. I brought the Matco Wheels. I went on the word of Roger but haven’t yet removed the current wheels and brakes to see if the new Matco axle bolt pattern will match. Could I speak with you or your mechanic by phone to get more info? Any help would be greatly appreciated.

Many thanks,

Evan Reisman

 
 
 

New from Zenith:

Zenith Planes For Sale 
  

Classified listing for buying or selling your Zenith building or flying related stuff...

Custom Instrument Panels
for your Zenith:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, Dynon and Garmin avionics, and more.

Zenith Homecoming Tee:

Zenair Floats

Flying On Your Own Wings:
 A Complete Guide to Understanding Light Airplane Design, by Chris Heintz

Builder & Pilot Supplies:

Aircraft Insurance:

 
 

West Coast USA:

 
Pro Builder Assistance:

 

Transition training:

Lavion Aero

K&S Aviation Services

Aircraft Spruce & Specialty for all your building and pilot supplies!

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

© 2024   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service