METAL PREP FOR PAINT

Hi guys

I am at that stage where I am prepping for paint. I have heard many mixed stories of which products are suitable for the job.

An aircraft spray painter that I recently met has recommended that I scour using alumiprep, rinse, spray on alodine, rinse and dry, wax and grease remover and then paint.

Another friend of mine prepped his Savanah by scouring with water, scour with alumiprep, wax and grease remover and then paint.

Yet another method that another friend of mine has used is to scour with denatured alcohol (metylated spirits) and then paint.

Obviously the objective is to remove the oxide layer on the metal and paint it as soon as possible and I have just read that denatured alcohol does that very job so why use nasty chemicals like alumiprep. As any wash from the painting process floods to the ground just outside my shed, there is no way that I am going to use alodine and contaminate the ground with chromium where my son plays.

I have already purchased some alumiprep but I am concerned with what might happen if trace amounts of it get caught in crevices inside the structures. On the other end of the scale, I have an aquaintance  that has a 601 HD that is painted and unflown and has been in a shed all of its life. It has bubbly corrosion on the metal pushing the paint up. I have no idea what prep work that he did.

So, is denatured alcohol enough to stop corrosion on a project that is 3 years old? I am thinking that it might be and as a final wash, it certainly dries nice and quick when compared to water. This means that I can get my epoxy primer on very soon after prepping instead of hours down the track.

 

What have you used to prep the aluminium on your plane? What other toughts do you have on the topic?

 

Phill

Views: 5421

▶ Reply to This

Replies to This Discussion

Permalink Reply by Jake Reyna on July 10, 2011 at 8:04am

Hey Phill, check out this site http://www.stewartsystems.aero/default.aspx

I'll pass on some advice from experienced builders I have met over the years, these guys have built over 40 airplanes. They're building RV's now, 2 or 3 a year. Wait at least a year before painting the airplane, not including the fiberglass. The DAR gave the same advice after inspecting my airplane. At minimum, wait until you do your Weight & Balance before painting.

6061 Aluminum is corrosion resistant and can be polished. The link listed offers some products that might be useful, just in case.http://www.stewartsystems.aero/catalog/3afff6e7-8eea-4019-840d-f362...

 

Jake

Permalink Reply by Ken Ryan on July 10, 2011 at 10:09am

Stewart Systems has a series of five videos on youtube:

 

http://www.youtube.com/user/stewartsystems#p/c/A25476026D68521C/0/y...

 

 

Permalink Reply by Paul Hammond on July 10, 2011 at 11:15pm

just paint the bloody thing

 

Permalink Reply by Jacob on July 11, 2011 at 7:05am

Hi Phill,

 

Like you I wanted to avoid alodine etc for obvious reasons.  What I did stumble upon at my local aviall was a product called PreKote surface pretreatment.  I've been using it to prepare all my parts before painting and it seem to work great.  The whole process is very easy all you do is spray it on the part with a normal household spray bottle then scrub the surface down with scotchbrite.  You then wait a minute do the same thing again then rinse it off with water and let it dry.  It foams up like soap when you scotchbrite the aluminium and looks as though it turns the aluminium oxide black like when you use rust convertor on steel.   Haven't had any parts sitting round long enough to know what it's like long term but they say in there promo that the us airforce now uses it so I figure it must work quite well.  It was about $60 to $70 dollars for the kit which included a 1 gallon/3.8 litre bottle which looks to be enough to do a whole aircraft.  The mob that produce it are called pantheonchemical who have a website pantheonchemical.com. 

Permalink Reply by Ernest Jessee on June 30, 2015 at 11:11am

Jacob,

How has the PreKote worked out.  Is your paint adhering?

Permalink Reply by Phill Barnes on July 11, 2011 at 7:45am
Hi guys
Thanks for the advice and motivational comments. I have decided to scour with the denatured alcohol and rinse with the the alcohol and slightly acid tank.water followed by a wipe down with thinners and alcohol mix just before paint.

Once again, thanks for your help and I will post some pics when I have something to show.


Regards
PHILL.
Permalink Reply by Chris Sinfield on July 12, 2011 at 6:43am

And what primer and paint did you end up using?

Chris

Permalink Reply by mike blemenschutz on July 18, 2011 at 5:08pm

I will assume that we are prepping 6061 T-6 alu.  the right way would be to etch with alodine 1200S  red scotchbrite and water to get your water breakfree surface, apply alodine. let dwell to a light gold tone. rinse throually. NOTE: its much better to do this process on parts prior to assembly to avoid alodine becoming trapped in areas where you cannot reach to rinse.

 

just prior to prime, a wiping with .a light solvent  isopropal alchol is fine....lightly tack than prime. best to use a good two part epoxy polimide primer most need to be top coated with paint within 8 hrs of priming.. 

 

If assembled and you have to alodine a one step alodine can be used.

 

google na-01-1a-509  its the navy's aircraft corrosion control bible 

 

good luck!!

 

mikeB  

 

Permalink Reply by Glenn Andressen on August 3, 2011 at 9:34pm

Hi Phill,

The first method you mention here is similar to that a friend of mine used on his RV7, but he said scour with methylated spirits. He carted his RV off to an automotive spray painter and they used a two pack.

A paint seller I questioned advocated the Alodine, citing that's what RV builders do, but remember, they are built with 2024, which is Alclad, different to the 6061 we are using.

Glenn.

RSS

New from Zenith:

Zenith Planes For Sale 
  

Classified listing for buying or selling your Zenith building or flying related stuff...

Custom Instrument Panels
for your Zenith:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, Dynon and Garmin avionics, and more.

Zenith Homecoming Tee:

Zenair Floats

Flying On Your Own Wings:
 A Complete Guide to Understanding Light Airplane Design, by Chris Heintz

Builder & Pilot Supplies:

Aircraft Insurance:

 
 

West Coast USA:

 
Pro Builder Assistance:

 

Transition training:

Lavion Aero

K&S Aviation Services

Aircraft Spruce & Specialty for all your building and pilot supplies!

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

© 2024   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service