Gearbox oil seepage - ideas?

48 state gearbox on a Viking 130.

I can't track down the source of this oil seepage and hoping you all have some other ideas. I figured I'd throw it out here before bugging Jan since I know they're busy plus this might help someone else too.

This isn't a whole lot of oil but this is after a 1/2 hour flight.  There are definitely some drops pooling plus some blown back on the upper parts behind the gearbox.

Things I've done:

 - replaced temp sensor

 - replaced the plug in the spare hole

 - replaced the o ring on the fill hole plug

 - tried to tighten the lug that is top front

 - used loctite 567 high temp thread sealant on the temp sensor and the spare plug

 - tightened both plugs on back of box and overflow port.

 - no oil on lower portion of gearbox or engine

 - no dripping or oil puddles after long sits in the hangar

- I've ziptied tightly rolled paper towel around the base of both the temp sensor and spare plug before flight.  Both were dry on the inside part after the flight yet still oil seepage so 99% sure the oil isn't coming from them.

 - The last thing I tried last night was the new o ring but didn't get to try to wrap it in paper towel to test. It might be hard to zip tie that part.

- I can't see oil seepage while idling on the ground. It might be happening but I just can't get too close due to the prop.

Any ideas?  

Thanks - Jim

Views: 250

Attachments:

▶ Reply to This

Replies to This Discussion

Permalink Reply by Jan Eggenfellner on September 11, 2023 at 7:55am

Hey Jim, are you sure it is gear oil and not coolant? -Alissa

Permalink Reply by Jim Davis on September 11, 2023 at 11:18am
Good thought Jan. I’ll look into that as soon as I get back in town later this week.
Thinking about the viscosity during all the times I’ve wiped it clean to try something new, I’m almost positive it’s oil and not coolant.
If I can get back from Chicago on Friday night, I’m planning on going up to Zenith on Saturday.

Thanks - Jim
Permalink Reply by Jim Davis on September 19, 2023 at 11:45am

Update - I met Jan and Alissa at the Zenith Homecoming last weekend.  Jan noticed right away that the brass plug was cross threaded.  We replaced the plug and screwed it in correctly with loctite 567.  

 Unfortunately that didn't fix the problem.  I tried a few more things such as washers and even re-tap just a little but all to no avail.

 Reading on-line - most people recommend a permatex thread sealant and locker.  I applied that yesterday.  The directions say 72 hours for a full cure so it will sit for about a week now until I get back from a work trip.

 I'll update you all next week.

 - Jim

Permalink Reply by Glenn Davis on November 20, 2023 at 9:00pm

Hey Jim,

got an update on the leak?

RSS

New from Zenith:

Zenith Planes For Sale 
  

Classified listing for buying or selling your Zenith building or flying related stuff...

Custom Instrument Panels
for your Zenith:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, Dynon and Garmin avionics, and more.

Zenith Homecoming Tee:

Zenair Floats

Flying On Your Own Wings:
 A Complete Guide to Understanding Light Airplane Design, by Chris Heintz

Builder & Pilot Supplies:

Aircraft Insurance:

 
 

West Coast USA:

 
Pro Builder Assistance:

 

Transition training:

Lavion Aero

K&S Aviation Services

Aircraft Spruce & Specialty for all your building and pilot supplies!

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

© 2024   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service