Jabiru 3300A - Starter Solenoid

Hello Everyone, 

Does anyone have a Starter Solenoid Wiring Diagram for a Jabiru 3300A. I have a wire that has a capacitor attached to the Solenoid, and I don't know where it goes to.

Thanks for your help!

Views: 135

▶ Reply to This

Replies to This Discussion

Permalink Reply by John Austin on June 8, 2024 at 11:28am

Any possibility it's a diode rather than a capacitor?  It's common practice to run a diode across the solenoid's terminals to prevent arcing in the start switch and burning the terminals.  I don't have a pic with a clear view of the diode across the starter solenoid, but here's a pic that shows the diode across the terminals of the master solenoid (the solenoid on the left in the picture):

John

N750A

Permalink Reply by Adel Bazzi on June 8, 2024 at 8:02pm

Hi John, thanks for your reply. I was hoping that you would. 

Here are a couple pictures showing the Blue Connector coming out of my Solenoid, with the Diode wrapped in heat shrink, however the other end of the Diode is not connected to anything, and that’s the one that I don’t know where to connect. 

Thanks again!

Adel Bazzi 

Attachments:
Permalink Reply by John Burns on June 9, 2024 at 12:42pm

I have attached the Jabiru installation manual, which includes the wiring diagrams.  It can be helpful at times.  JEM3302-8_Inst-.pdf

Permalink Reply by Adel Bazzi on June 9, 2024 at 12:51pm

Hi John, 

Thanks for the reply. I had already gone through this, and unfortunately no mention of the Diode on it. This is very vague. 

Thanks!

Adel Bazzi

Permalink Reply by Bob Simmons on June 10, 2024 at 5:36pm

Master and starter solenoid diodes connect differently. If this is your starter solenoid, and the cathode (with the stripe) is going to the solenoid, the other end (anode) should go to ground.

This might help:

https://www.kitplanes.com/aircraft-wiring-4/

https://www.youtube.com/watch?v=rKz6NSTaGRE

Permalink Reply by Adel Bazzi on June 11, 2024 at 12:25am

Hi Bob, 

Thanks for your reply. This is exactly what I needed.

Question… Do you know if there is a specific size Diode that I need for my Starter Solenoid? I accidentally broke the one that was attached to the solenoid, and I need to replace it now. 

Thanks again!

Adel Bazzi 

Permalink Reply by Bob Simmons on June 11, 2024 at 1:20pm

1N4001 or 1N4004 are commonly used. The 4004 has a higher current rating, so I'd go with that.

Permalink Reply by Bob Simmons on June 12, 2024 at 10:53pm

26 cents at Mouser.

Permalink Reply by Adel Bazzi on June 13, 2024 at 7:15pm

Perfect! Thanks again for your help. 

Adel Bazzi 

RSS

New from Zenith:

Zenith Planes For Sale 
  

Classified listing for buying or selling your Zenith building or flying related stuff...

Custom Instrument Panels
for your Zenith:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, Dynon and Garmin avionics, and more.

Zenith Homecoming Tee:

Zenair Floats

Flying On Your Own Wings:
 A Complete Guide to Understanding Light Airplane Design, by Chris Heintz

Builder & Pilot Supplies:

Aircraft Insurance:

 
 

West Coast USA:

 
Pro Builder Assistance:

 

Transition training:

Lavion Aero

K&S Aviation Services

Aircraft Spruce & Specialty for all your building and pilot supplies!

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

© 2024   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service