All Blog Posts

Search Blog Posts

Zenith 750 Cruzer, Attaching the front wheel gear

November 9, 2024

Attaching the front wheel gear.

Installed the SAFETY ALERT – DECEMBER, 2023, Nose gear bearing, C75L3-1 side plates, AN3-42A, AN3-43A.

Tapped 2 rear holes and countersunk 2 front holes.…



Continue

Added by Alexander Samoylovich on January 20, 2025 at 9:24am — No Comments

Zenith 750 Cruzer, Painted the cabin frame

October 7, 2024

Primed and painted the cabin frame.

Checked the need of washers on the forward fuselage. Since the drawings are not always correct I had to check every bolt kind for the number of required washers.…



Continue

Added by Alexander Samoylovich on January 19, 2025 at 9:34am — No Comments

Zenith 750 Cruzer, Attached the firewall

October 5, 2024

Attached the firewall.
Cleaned and deburred the cabin frame.
Attached the struct mounts.

Added by Alexander Samoylovich on January 17, 2025 at 8:01am — 1 Comment

Zenith 750 Cruzer, Attached the break cylinders

October 3, 2024

Riveted the break cylinders angles and bolted the cylinders to them.

Added by Alexander Samoylovich on January 16, 2025 at 7:57am — No Comments

Zenith 750 Cruzer, Riveted the break pedals

October 1, 2024

Riveted the break pedals.

Added by Alexander Samoylovich on January 13, 2025 at 8:21am — No Comments

Zenith 750 Cruzer, Bent the break pedal hinges

September 30, 2024

Using vise and hummer bent the break pedal hinges.

Added by Alexander Samoylovich on January 11, 2025 at 9:29am — No Comments

Zenith 750 Cruzer, Started clecoing the front fuselage

September 29, 2024

Started clecoing the front fuselage for the final assembly.

Added by Alexander Samoylovich on January 6, 2025 at 9:14pm — No Comments

Zenith 750 Cruzer, Deburring the front fuselage

September 26, 2024

Painted the strut mounts.
Deburring the front fuselage parts.
Tested the torque tube rear bearing fitting. Not good. Talked to Zenith. They will send me a new bearing.

Added by Alexander Samoylovich on January 3, 2025 at 8:22am — No Comments

Zenith 750 Cruzer, Disassembled the front fuselage

September 25, 2024

Primed the left strut mount.
Disassembled the front fuselage.
Ready to deburring.

Added by Alexander Samoylovich on January 2, 2025 at 7:24am — No Comments

Zenith 750 Cruzer, Primed the right strut mount

September 23, 20224

I drilled the skin holes incorrectly. They are elliptical. Drilled a set of holes below.

I am thinking about adding rivets in between the bad holes. The spacing allows it. Rivet A5 is 4 mm, the current distance between holes is 25, 29, 35 mm.

Zenith recommended to use A6 rivets or AN3 bolts for the damaged holes. I opted for the bolts.…



Continue

Added by Alexander Samoylovich on January 1, 2025 at 8:59am — No Comments

Zenith 750 Cruzer, Drilled holse in the front wheel fork

September 12, 2024

Drilled holse in the front wheel fork and doubler.

Added by Alexander Samoylovich on December 31, 2024 at 7:52am — No Comments

Zenith 750 Cruzer, Put rubber pucks on the front wheel leg

September 08, 2024

Put rubber pucks on the front wheel leg. Used silicon grease on the leg.

Added by Alexander Samoylovich on December 30, 2024 at 9:02am — No Comments

Zenith 750 Cruzer, Control rods

September 02, 2024

Attached flapperon vertical and horizontal control rods.

Added by Alexander Samoylovich on December 29, 2024 at 3:18pm — No Comments

Zenith 750 Cruzer, Control Mixer

September 1, 2024

Assembling the flapperon actuator and the control mixer.

Used 9V battery to check if the actuator can turn the mixer bar.

By Zenith advise used ACF-50 as the lubricant. It looks like it works.…

Continue

Added by Alexander Samoylovich on December 25, 2024 at 10:32am — No Comments

Zenith 750 Cruzer, Painting steel parts

August 31, 2024

Painting steel parts. Rust Oleum self etching prime and Rust Oleum glossy smoke grey enamel.

Added by Alexander Samoylovich on December 24, 2024 at 1:04pm — No Comments

Zenith 750 Cruzer, Matching strut mounts to the landing gear channel

August 28, 2024

Continued filing the gear channel and the strut mount bracket to match.

Added by Alexander Samoylovich on December 15, 2024 at 8:35am — No Comments

Zenith 750 Cruzer, Started painting aileron pedals

August 15, 2024

Started painting aileron pedals. One part is the original one another one is sanded before priming.

Added by Alexander Samoylovich on December 13, 2024 at 7:14am — No Comments

Zenith 750 Cruzer, Fabricating the emgine mount fittings

July 31, 2024

Ground the top engine mount fittings.
Drilling the top engine mount fittings.

Added by Alexander Samoylovich on December 12, 2024 at 7:31am — No Comments

CH601UL is growing in Italy

Added by Massimo Piva on December 11, 2024 at 1:12pm — No Comments

Zenith 750 Cruzer, Drilled sides of the cabin frame

July 30, 2024

Drilled sides of the cabin frame.

Added by Alexander Samoylovich on December 11, 2024 at 11:15am — No Comments

Featured Blog Posts

View All

Latest Blog Posts

Most Popular Blog Posts

Monthly Archives

2026

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

1999

New from Zenith:

Zenith Planes & Parts For Sale 
  

Classified listings for buying or selling Zenith builds and parts...

Custom Instrument Panels
for your Zenith:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, Dynon and Garmin avionics, and more.

Zenith Homecoming Tee:

Zenair Floats

Flying On Your Own Wings:
 A Complete Guide to Understanding Light Airplane Design, by Chris Heintz

Builder & Pilot Supplies:

Aircraft Insurance:

 
 

Transition training:

Flying Knuckleheads

Lavion Aero

Aircraft Spruce & Specialty for all your building and pilot supplies!

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

Save the date: 2027 Zenith Homecoming - Open Hangar Days and Fly-In: September 17 & 18, 2026

© 2026   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service