If your finished Zenith aircraft isn't flying quite hands-free and is consistently demonstrating a "heavy wing," Roger and Steve from the Zenith Aircraft kit factory provide an easy fix:

Share with us your additional comments and suggestions below, and let us know how this worked.

Check out the video above of the flour bombing practice drops Roger and Dennis did this morning to get ready for the Flour Bombing Contest at Open Hangar Days 2016!…

Just thought I would post an update on the condition of the vinyl wrap that covers my entire 701, after five years.



In short, it still looks brand new! Everywhere  I go people ask me what it cost for the paint job. They are shocked that my 701 is not painted! They walk up close and look at the rivets and tell me that I am pulling their leg! I can only convince them by showing them a seam.



About three years ago a tire went flat and, since the fuel tanks were full, the upper…

The Zenith Aircraft STOL Competition is a crowd favorite at the Open Hangar Days! The exciting event is sponsored by Kitplanes Magazine and is sure to please the crowd again this year for the…

The addition of new activities and two full days for the 25th Annual Open Hangar Days at…

I flew my CAMit-powered (RIP) 601 to AirVenture 2016. This was its third trip to OSH.  It’s just over 1,800 statute miles each way from Santa Rosa California.

I usually try to work some sightseeing into my trips. I love to fly in the mountains and along rivers. I have spent many hours doing so in the west. This year my idea was to follow the Missouri River…

You are invited  to attend the seminars and engine panel discussion presented at the Open Hangar Days at …

Look who got into Kitplanes! (2nd one down)

KitPlanes Completions

In August 1986, in tiny Stanley, Nova Scotia, I bought a ride around the patch in a 2-place canoe with wings. For 30 years, I studied "Low & Slow" -- the laws, the flaws, the struggles to make it grow. I watched it blossom and evolve, and blossom again. And after I retired, I made a decision, 'pulled the trigger', and bought a kit. In August 2016, a Zenith CH-750 STOL kit arrived outside my single car garage in suburban New York. And now, the journey begins. :-)

My Zenith builder partner and I were looking for a cheap way to house our 750 and 650 aircrafts in a single hangar and save some expense, this is our solution built from a modified Harbor freight lift table.  The 750 is lifted high enough to roll the 650 under the wing and then lowered again.  The table is rated for 1000 lbs. and raises our planes 18" off the floor, we have…

Two groups have banded together for a common goal with EAA Chapter 1083 and John Robinson, the founder of AV84all.org…

Thinking of extending nose strut by about 2 inches for clearance in case of off road bungee failure.  I've got large mains and standard nose wheel.  Anyone else?  Input appreciated.  Cheers,,, Lynn

So while I await an answer from Zenith on my "elevator issue", I have moved on to other areas in the project. Can someone that has been before me help me with this. I am wiring the panel using the Composite Design Mini panel. Everything from the primary bus, and the avionics bus has been pretty simple. 18AWG does the trick for all these low draw items. I need help with the gauge wire needed for the other items. Master switch to battery relay, alternator switch to control, and back to the…

Milestone:  1st Viking 110 Startup at 9:45 AM, Saturday, July 30th ... Fixed plumbing problem then after about 5 or 6 sec. of cranking and one loud backfire, smooth and quiet purring ... Most impressed ... Ran about 20-30 sec. (without prop) with EIS values good and shutdown normally.  I'll be mounting the WarpDrive prop wit pitch 12 deg. (?) later this week for a real startup.

Jon had a great showing of his CruZer in KITPLANE 

Jon in KITPLANE

Viking in KITPLANE 

The 180 hp engine they mentioned will be installed in my CH-750 CruZer

Already looking forward to the first flight :)

Jan

Whoo Hoo!

Received my Special Certificate of Airworthiness from Transport Canada Today.

3 1/2 years of pushing myself and learning new things. Wow, what a ride that has been!

Thank-you to everyone on this site who has asked questions, answered questions, made comments or contributed in any other way to this fantastic community.

Would not have done it without you!

Cheers,

Bill Moore

C-FFWF Stol CH750 UL 350is