I had the Zenith cabin heat option installed in my plane, but it wasn't working very well, and I didn't like it at all. I removed it completely.

Has anyone installed a cabin heat box obtained somewhere else that they like ? I would prefer one that dumps the heat when the cabin heat is off. I was considering one of the Van's heat boxes shown here :

http://www.vansaircraft.com/cgi-bin/store.cgi?ident=1479305840-320-...

Has anyone installed one that is a simple installation ? If so, a photo or two would be nice.

Although I couldn't find one, I would really like a slide control rather than a rotating flapper to turn the heat on and off.

Thanks, Jim

Views: 1937

Reply to This

Replies to This Discussion

I use the waste heat from my firewall mounted oil cooler to heat the cabin. No heat muff around the exhaust. No extra SCAT tubes. It does have a rotating flap.

The Jabiru cabin heat box dumps the heat when not diverting it to the cabin:

It uses a control cable to turn the heat on and off. Spruce sells something identical - they even have 2 versions as to where the hot air duct comes in.

John

N750A

I used the Vans TG10 with my UL heat muff. Has an exterior NACA vent into the muff and then to the vent.

Dumps the heat out bottom of the cowl when not in use.

Works great..

Flew last winter when outside temps in teens at altitude and very tolerable in cockpit.

Jerry

Thanks for the info. I've been looking at the Vans boxes and the similar ones at Aircraft Spruce. 

Jim

John,

The boxes I've looked at do not have anything like the triangle and vertical arm making up your actuator. I believe something like that would be desirable no matter which box I get. Did you make those parts, or did they come with your box ? I could probably make something similar. Of the 4 bolts shown, is the right bottom one anchored to the box ? Could you possibly tell me what makes up each pivot point (bolt, spacer, nuts, etc) ?  

Thanks,  Jim

P.S. I just realized my reply to you is not going directly under your reply, or getting indented like my reply to Jerold. I deleted and tried it twice. The only difference is that my reply to Jerold was the last in the thread so it had to go under his reply, but it did also get indented. Is this a problem ? I never noticed this happening before.

You're correct - I made the triangular bellcrank and linkage arm myself.  Looking at the photo of my installation, the short black arm in the left lower corner of the heat box is the original lever to activate the valve.  The way it is positioned, you'd have have a sharp 90 degree bend in the cable to actuate it - no good!  The linkage I added allows the cable to come straight through the firewall to actuate the linkage - much better!

The bolt on the lower right of the bellcrank is a pivot that is anchored through a hole I drilled in the box and secured with a jam nut against the box and the bellcrank is secured with a castellated nut.  The remainder of the bolts are pivots with washers and metal lock nuts (could use castellated nuts since these are rotating parts, but hey, it's not a F-16 and this isn't exactly a critical assembly! Ha!) - you can just use washers for spacers as necessary to keep the linkage aligned.

The Jabiru 750 Firewall-Forward instruction guide has several pictures of a similar cabin heat linkage:

STOL 750 Firewall-Forward Instructions

John

John,

Great design. I was concerned about the way I would connect my heater cable. You solved that problem. The link you have listed gives me a "404 Not Found Error", although it gets to a Jabiru web page.

Thanks Again,

Jim

I fixed the link - should work now!

John

James

I have this cabin heat box installed on my 750:

http://www.aircraftspruce.com/catalog/eppages/homebuilderscabinheat...

I have the heat box connected to a full muffler wrap heat muff which is supplied with outside air via naca duct.  Lots of heat.

Tim

Thanks for all the replies. I put one of the Vans Stainless Steel boxes on my letter to Santa. If he comes through, I'll copy John's bellcrank design to use with the control.

Jim

RSS

New from Zenith:

Zenith Planes For Sale 
 

Classified listing for buying or selling your Zenith building or flying related stuff...


Custom Instrument Panels
for your Zenith
:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, Dynon and Garmin avionics, and more.


Zenith Homecoming Tee:


Zenair Floats


Flying On Your Own Wings:
A Complete Guide to Understanding Light Airplane Design, by Chris Heintz


Builder & Pilot Supplies:

Aircraft Insurance:

 
 

West Coast USA:

 
Pro Builder Assistance:

 

Transition training:

Lavion Aero

K&S Aviation Services

Aircraft Spruce & Specialty for all your building and pilot supplies!

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

© 2024   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service