Bob Hartunian
  • Fawnskin, CA
  • United States
Share on Facebook

Bob Hartunian's Friends

  • Coenie
  • Jon Humberd
  • Lee DeLano
  • Martin Bima
  • Joe Spencer
  • Perry Delano

Bob Hartunian's Discussions

GRT 912 EIS -Wanted

Started Sep 3 0 Replies

I need a working Grand Rapids EIS for a 912 engine; old one stopped working.bobh5@earthlink.netContinue

Ignition Switch

Started this discussion. Last reply by Glen Clarke Sep 11, 2021. 7 Replies

Does anyone have a 701 keyed ignition switch at reasonable cost?Continue

912 Ignition Coil

Started this discussion. Last reply by Bob Hartunian Jun 9, 2021. 2 Replies

I need a 912 dual ignition coil that works.Continue

Wanted-3" Sensitive Altimeter

Started this discussion. Last reply by Timothy Sparks Jun 27, 2021. 6 Replies

If someone has a 3 1/8" dia sensitive altimeter to 10-20K' that works at reasonable price, please contact me.Bob HContinue

 

Bob Hartunian's Page

Latest Activity

Bob Hartunian posted a discussion

Ignition Switch

Does anyone have a 701 keyed ignition switch at reasonable cost?See More
Aug 5, 2021
Bob Hartunian posted a discussion

912 Ignition Coil

I need a 912 dual ignition coil that works.See More
Jun 9, 2021
Bob Hartunian posted a discussion

Wanted-3" Sensitive Altimeter

If someone has a 3 1/8" dia sensitive altimeter to 10-20K' that works at reasonable price, please contact me.Bob HSee More
Mar 29, 2021
Thomas Hudgins left a comment for Bob Hartunian
"Bob Hartunian Tie wraps are fine in most instances. However ANYTIME you are using them in an area where high heat is the norm, "never" use the standard Nylon tie wraps. Go the extra cost and use Tefzel or Peek tie wraps. These are designed…"
Feb 16, 2020

Profile Information

Aircraft Model
STOL CH 701
Project Status
Less than half
Building From
Partial kit
Engine installed (or plan to install)
Rotax 912
Building Experience
Have already built an airplane
Flying Experience
Private Pilot
Building and Flying Info / Your Profession / Other Background Info
Retired after 42 yrs working in aircraft companies specializing in composite structure manufacturing.
Degrees in mechanical/materials engineering.
Built and fly a Pulsar XP with 900 hrs on plane out of high altitude airport, L35.
Fabricating 701 for desert and mountain flying into rough strips for fishing trips.
Home Airport (ie. KMYJ)
L35

Bob Hartunian's Blog

Poor performance at higher Altitudes

Posted on April 12, 2021 at 9:52am 10 Comments

I fly my 701 out of a 7000' airport, L35, and have a 912 engine with high comp pistons installed to produce about 90 hp at sea level. Plane has the fixed slats installed. The plane's performance is so marginal that I can not take a passenger because the plane will not climb over 50 mph with nose abnormally high just to stay level in the air. However at lower altitude airports of 3000', performance is better and there is better flying margin and I can climb at 400 fpm solo.

The plane…

Continue

Comment Wall (3 comments)

You need to be a member of Zenith Aircraft Builders and Flyers to add comments!

Join Zenith Aircraft Builders and Flyers

At 11:56pm on December 9, 2021, Coenie said…

Thank you for the info.

At 3:58pm on February 16, 2020, Thomas Hudgins said…

Bob Hartunian Tie wraps are fine in most instances. However ANYTIME you are using them in an area where high heat is the norm, "never" use the standard Nylon tie wraps. Go the extra cost and use Tefzel or Peek tie wraps. These are designed for use in High Temp and are chemically resistant compounds that will take the beating that Nylon will give up the ghost on in an instant.

https://www.nelcoproducts.com/cable-ties-materials-specifications/

At 8:29am on July 9, 2016, Lee DeLano said…

Followed plans without much thought about separate fuel filters.

I usually do my own fueling from 5 gal. cans and airplane is stored in a hangar year round.  Normally have replaced the single filter annually during normal maintenance.  The clear plastic filters allow pre-flight inspection.  The quick drains have caused more problems - a small piece of grit/dirt will interfere with the spring loaded seal and have a tendency to leak.

I did install a shut-off valve on the tank discharge line so each tank could be isolated.  It is safety wired in the "OPEN" position and operated annually.

Additionally, I installed an electric fuel pump and spliced in a fuel pressure gauge line at the top of the engine (Rotax 912ULS) and routed line to gauge in panel.  Along with that, I added a vent line from the existing fuel split at the top of the engine and ran a nylon line back to the fuel tank - used PVC drip irrigation fittings to make 90 degree bends - the line is on the pilot side and the air bubbles can be seen going back to the tank.

Have been operating since 2010, approx. 200 hours, the system has been running successfully.  Annual maintenance and inspection are important for this system.

My grandkids live near Sparks, NV and the highest airport I have operated from is Spanish Springs (N86).  I used to commute from Modesto to El Centro and would regularly fly-by Big Bear, but never landed there.  You will enjoy the airplane - I love mine.  I do go to Gravelly (1Q5) once or twice a year, a truly gravelly runway - experienced rock nicks and erosion in the composite prop - updated the prop with metal tips from Warp Drive - would recommend if you are headed to unimproved strips.
Thanks for the comments.  Usually attend fly-in at Cloverdale in the spring, maybe I'll see you there.

 
 
 

New from Zenith:

Zenith Planes For Sale 
 

Classified listing for buying or selling your Zenith building or flying related stuff...


Custom Instrument Panels
for your Zenith
:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, Dynon and Garmin avionics, and more.


Zenith Homecoming Tee:


Zenair Floats


Flying On Your Own Wings:
A Complete Guide to Understanding Light Airplane Design, by Chris Heintz


Builder & Pilot Supplies:

Aircraft Insurance:

 
 

West Coast USA:

 
Pro Builder Assistance:

 

Transition training:

Lavion Aero

K&S Aviation Services

Aircraft Spruce & Specialty for all your building and pilot supplies!

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

© 2024   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service