I didn't see anything in the plans about aileron controls stops. Any comments on what to do there?

I like it when I can use the word "uber". It just sounds cool. Anyhow, the photo below shows my garage for the next year. It's small, I mean like real small. Breaks down like this.....

I once had a really cool house with a really nice sized garage, that was 6 months ago. The plan was to buy a new home so the house went for sale. It had an offer 5 days…

Well, it's as good a time as any to start. The plans are still a blur but I should be able to get through the rudder. I'm scratch building but I can see where buying parts is a real advantage so I'm sure I'll be buying parts. Zenith prices are pretty cheap, all things considered. 

Building the sheet metal brake

Anyhow, I need to build a brake. I'm a self employed plumber so I made some time today…

I completed most of the wiring in the panel before firing up the Dynon. All went well, recognized all systems. This was the first time I rolled it out into the backyard since I started the build 3 1/2 years ago.

Has anyone had the canopy of 601 XL open during the flight ??

My canopy opened in flight at 1500' at 100 kts early this month (May 2013). The aircraft dived towards the land and was hard to control. The canopy stayed up in the air and I could not pull it down. I slowed down to 60 kts and droped down to 500' just in case I had to land on the beach. All the items got sucked out from the back including my head phones. I turned back to the airport, about 2 miles. I  could not communicate…

In exchange for your feedback, I have made the application free until to 12 May 2013.



The new version releases soon, so grab a copy while you can.

A bit about the application

Aircraft Builder helps you capture your progress using your iPad, and generate a build log when you are done.

-The dashboard gives you a quick overview of the project and instant access to the tasks that are in progress.

-The application allows you to capture…

2018 UPDATE: See the follow up photos and videos in the comments below this original story.

Zenith builders and pilots are made up of a very interesting group of individuals, and continue to be a source of inspiration.  Here's a brief story of one of them that was recently featured in the news:…

Friday I felt like I needed to do something that could be construed as actual work toward creating the plane. To preface this I will try to explain my parts fabrication ideas. Sorry about the long-windedness.

I have seen here and other places that while builders are making parts they have damaged them in some way or have had to remake the part for some reason. In thinking about this I decided that I need some way to be able to remake the part without having to spend any more time than…

More questions from the rookie.

Still playing with heat issues, but a new opportunity has surfaced. While taxiing to the active, my battery charge indication shoed low voltage, fluctuating into yellow. On run-up, the bar still showed slightly more than 12 volts. It usually reads 13.2 or so. I went back to tie down, and quit for day. Later, the battery would not turn engine. On charger all night.

Does the Jabiru have a voltage regulator that may be bad? If so,…

Hi All,

I have just completed a 701 and have 5hours air time everything is awesome with the exception that the plane wants to roll to the left.  What is the recommended roll trim fix?

Claude

I acquired a 750 project from another builder.  I am going to be hanging an O-235 on it, so I have no need for the Jabiru 3300 cowl and mount.

$795 plus shipping for both.  That's 50% of the cost of purchasing new. 

fast weekend trip- BWI to JAX - rental car to WW for my 2850cc and

Dan's new crank w/5th bearing - nice visit w/WW but too short- fast drive home

Fred Schutt

I took over a CH-750 project that was started by another builder.  I am installing a Lycoming O-235, and the standard 12 gallons tanks just aren't enough.  I have TWO standard 12 gallon tanks with sending units installed in perfect condition that I will sell for $500 (total for both) so that I can apply that money towards the 15 Gallon tanks, or I will give you $500 for your standard tanks (so that you can upgrade) and I'll just install Four 12 gallon tanks.

Any takers?

Having recently finished the CH 750 elevator, I resumed work on the stabilizer. You may recall that I damaged the skin on the stabilizer when I laid the upper skin side on the bottom of the skeleton and riveted the entire side before I realized what I had done. In removing the rivets, I damaged the skin enough that I had to buy a new one during my visit to the factory during the September fly-in and open house. Today, I finished the major assembly of the stabilizer and now have to attach the…

(690 Hours total time.)

(The following is my opinion) ...

I bought it, I built it, I maintain it and I…

Last week I came across a gentleman that was selling sheets of 6061-T6 (12 - 0.016, 4 - 0.025, 1 - 0.032 and 1 - 0.040 all sheets are 12'x4') and a Corvair engine. As luck would have it he lives only 20 miles from me! My son and I went last Saturday to…

So here is my idea for a make-shift drafting desk. I ordered 2 aluminum squares from Amazon (I have the Prime, so get free shipping on most items). I screwed one to the table top and the other can slide for the straight edge. I wish I could…

I am finally working on the rt. tank and fuel system prior to closing the right wing. I did some research on sealants for the stock welded fuel tanks - so I should never have any leakage problems!!

Tapered pipe thread fittings -

I have long experience using either Loctite # 592 - Pipe sealant with Teflon (PST) or Permatex pipe thread sealant on fuels, oils and high pressure gases. Both sealants cure when air is excluded and have teflon in them to prevent galling of metal pipe…