All Blog Posts (2,351)

Ugly is only skin-deep

This VW ad from 1966 has become a classic and can still be seen in VW dealerships across the country.  The above is prominently on display as a large framed poster in a shiny new VW dealer in St. Louis. While  the cars have changed since 1966, the basic message remains the same.

Like the VW Beetle, the ad copy has become a classic too.  It caught my attention…

Continue

Added by Sebastien Heintz on October 25, 2011 at 11:00am — 11 Comments

Update October 2011

 Now have flown off the forty hour Phase One Testing.  All in all a very benign experience. No real supprises except for the first couple of takeoffs being soooo quick.

Also have done first condition inspection and the Rotax 25 hour checks (100 hour check) with no problems.

Experienced no cooling problems with temps this summer in OATs as high as 98 F. Engine is Rotax 912ULS with Zenith FWF kit.

Have installed the Zenith VG's and have plenty of elevator authority.  My…

Continue

Added by Phil Smith on October 23, 2011 at 4:18pm — 2 Comments

Next phase

I have used up all of the .016 through .040 material I had on hand making miscellaneous parts, (270 parts so far).  I laughingly call this method my plans built quick build kit figuring at the rate I am going in 3-5 years I'll would have enough parts to quick build an airframe.

I will be ordering the material for wing and center spars next week.  Here are a couple 

 

Added by Tim Smart on October 21, 2011 at 11:18am — 3 Comments

Aluminium grades ?

Hi All,
I have bought the plans to and still in the process of finding out all the relevant info on constructing the ch 750.
My question is in relation to specific Aluminium grades the plans call for the use of 6061 T6 or 2024 T3 etc. Does anyone know if they can  be substituted for 5083

Added by Mitch Torpy on October 19, 2011 at 5:23am — 7 Comments

thicker sheeting on wings

Anyone put thicker aluminum on wings of 750.  whats the pros and cons?

Added by Jesse Hartman on October 18, 2011 at 10:00am — 7 Comments

Lyc O-235 Installation Advice

I'm looking ahead to engine installation details - most likely for a Lyc O-235. (Yes, I know they are a bit heavier, etc., but I am familiar with Lyc engines and prefer to go this route.)

Seeking any advice on:

Engine mount - purchase or self built?

Cowling - will a CH601 fit ? (I have read that the 601/750 firewalls are the same size/shape.)

Cowling mounting arrangements - screws into the firewall flange?

Carb location - this varies with model # on other…

Continue

Added by Jim Oke on October 16, 2011 at 9:26am — 5 Comments

folding wings--taildragger

I just bought a partly started 801 kit. I am interested to know if anyone has built an 801 with folding wings and if anyone has built an 801 as a taildragger?

 

Thanks

 

Karl Hipp

Added by karl hipp on October 14, 2011 at 4:25pm — 1 Comment

wings mods

working on opening the wings to put the mod in place. and hope to be fly by spring of 2012.

Added by Ronald Hook on October 13, 2011 at 10:58am — No Comments

Zodiac XL b PROJECT FOR SALE

CH601 Zodiac XL – B     FOR SALE                $ 52,500.00      

Aircraft has not been registered or inspected.

You are purchasing an uncompleted kit.

51% does not apply as the original kit owner purchased and built the entire airframe.  He had kept a log book of his construction.  The original kit owner also installed the engine and avionics.

All structural upgrades have been completed at Flight Crafters.

Some minor work needs to be completed and…

Continue

Added by Russell Lepre' on October 10, 2011 at 7:16am — No Comments

folding wings

Are there many of you who have folding wings on your 750's?  Im wondering if they are a good option to build into the plan?  I have the blueprints for them just wondering if they work well.

Added by Jesse Hartman on October 8, 2011 at 6:38pm — 3 Comments

Corrosion Protection

Hi.  Wondering if its easier to buy zinc chromate in spray cans, or if I should buy the gallon?  Do you brush it on or spray it on? Also If I want to prime only mating surfaces is one gallon gonna be enough for a 750?  Any help would be great.

I know I ask alot of questions, and im sure there will be 100's more but I can give you guys my social # so you can claim me as a dependent If I get to needy :)

Added by Jesse Hartman on October 6, 2011 at 6:25pm — 6 Comments

Horizontal Stablizer

Visit of two friends at home to help with the Skin of the horizontal stabilizer of my750.



See more in www.stolch750.blogspot.com in…

Continue

Added by Gustavo Padovezi Tenuta on October 6, 2011 at 12:37pm — No Comments

Newsletter reminder

If you forgot to renew your Zenair News, you can subscribe with the pull down tab at the top of the toolbar. The next newsletter is about to ship!

Added by Zenair News on October 6, 2011 at 7:16am — No Comments

601 fuel issue

has anyone had any trouble with the 601 fuel system losing prime if it sits for a while ?

 I have had an issue with a 601 standard arrangement just like the plans call for . The line goes to the center counsel from the wings and then up to the fuel selector then down to the gasculator

i had the 601 sit for few weeks and then couldnt get it started , wich was strange becouse the 3300 usually fires right up , i tried to drain the gasculator and the fuel didnt come out at a steady…

Continue

Added by Tracy Buttles on October 4, 2011 at 4:30pm — 5 Comments

Low Cost Steering Boot solution for Zenith 601

I've been looking for rubber boots to use on the Zenith 601 steering arms. It has been difficult to find an off-the-shelf product due to the narrow profile. I finally found something that is a near perfect fit on my HDS. It can be purchased from JB-Custom Fabrication on E-bay. This particular boot is used on certain Jeep models for the twin shifters. It costs around $22.00 plus shipping. Good news is you only need to buy one and carefully cut it in half. The following steps describe…

Continue

Added by Chuck Long on October 3, 2011 at 2:47pm — 3 Comments

XL Jabiru CHT's



On my flight from Idaho to Prineville, my #3 CHT was running high. I had modified the system for diverting air, the left side was running well, so I went back to my original system on the right side. Still need to do some tweaking, but I'm happy with the numbers. The original diverters were made of fiberglass and I'm trying to recreate using aluminum to increase…

Continue

Added by Jake Reyna on October 2, 2011 at 9:30am — 3 Comments

Taildragger CG

I'm building a CH650 with the taildragger option.  Can I expect the empty CG to be more forward, aft or the same compared to a comparable equipped nosewheel CH601/650?

I can probably calculate the difference if I had accurate weight numbers for the nosewheel assembly.  I would assume the same weight for the mains, just a different moment arm.

Any info will be greatly appreciated!

 

Dale

(wings and empennage done, working on fuselage)

Added by Dale Medendorp on October 1, 2011 at 2:57pm — No Comments

Zenith 750 Xplane on iPad

Has anyone run this on XPlane for iPad ?   If so, how does the download work ?  Thanks.

Added by Gordon Arbeitman on September 30, 2011 at 10:00am — No Comments

Sheet metal supplier

I have been turnd onto a company called Metal Superstore.  They are local so no shipping is good, and they came up way cheaper than aircraft spruce.  For 10 sheets of .020 and 3 sheet of .025 they wanted 843.00 after tax. Aircraft spruce wants 1210.85 plus shipping. Thats 367.00 plus shipping cheaper. How ever they cant get .016. Check em out they have locations all over the US.

 

Added by Jesse Hartman on September 29, 2011 at 3:31pm — 2 Comments

Residual Fuel - 701 - with Downward Pitch

I am about to have my 701 finally inspected - next week I hope and have been calibrating fuel tanks, fuel flow etc and am a bit worried about the amount of residual fuel left in my tanks when simulating a downward pitch.



I have built a Czech Kit with the supplied fuel tanks - a bit larger than the American ones being longer at the "thin" trailing wing edge end. They hold 45 litres full and have the fuel outlet at the back inboard corner as with the "normal"…

Continue

Added by Jock Struthers on September 28, 2011 at 5:30pm — 5 Comments

Monthly Archives

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

1999

New from Zenith:

Zenith Planes For Sale 
 

Classified listing for buying or selling your Zenith building or flying related stuff...


Custom Instrument Panels
for your Zenith
:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, Dynon and Garmin avionics, and more.


Zenith Homecoming Tee:


Zenair Floats


Flying On Your Own Wings:
A Complete Guide to Understanding Light Airplane Design, by Chris Heintz


Builder & Pilot Supplies:

Aircraft Insurance:

 
 

West Coast USA:

 
Pro Builder Assistance:

 

Transition training:

Lavion Aero

K&S Aviation Services

Aircraft Spruce & Specialty for all your building and pilot supplies!

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

© 2024   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service