Flat gasket for Gascolator A10580-T

Brake pads for a Grove 30-1 caliper

Soft filter for carburetor intake on a Lycoming O-235

Thanks.

The crate arrived today after a couple of adventures.  Zenith shipped on May 24th and shortly thereafter the weather turned horrible.  I got a notice of a 'weather delay' on my crate and waited to hear if it went flying without me.  However, it arrived in NH on 06/01, and my house on 6/04.  The second worry was the forklift puncture at the water line of the crate.  (See photo).  The fork did travel into the crate however, the only damage was a destroyed corner of the packing list envelope…

My Cleco cans are filling back up as I rivet skins 

https://youtu.be/7iKZIRBEhdc
Cruzer circuit practice with full flap landings, plus coastal scenery flight; Fleureiu Peninsula, South Australia, at 8x speed, no music - 8 min/fast video. Last landing with half flaps and side slipped. Camera beneath the plane. For fellow Builders - keep going - a very forgiving plane, not fast.

20190517_172014.jpg

One thing that has often been a problem is trying to keep parts from getting lost as they wait to be added to larger assemblies. While I am scatchbuilding, the problem is no doubt worse for someone building from a kit because they get all their parts at once.

Something that has recently been quite useful for me is to use mini-stretch wrap.…

The April 2019 issue of AgAir Update, the monthly magazine for the agricultural aviation (crop spraying) industry, reprinted a flight evaluation article of the STOL CH 701 "Sky Jeep" light sport aircraft (first published twenty years…

Hi All,  9 min YouTube - new kitbuilt 750 Cruzer with a Viking engine.

Scenic lap of Hindmarsh Island, South Australia - best on a big screen.

At 6 minutes you can jump fwd to the end, for the landing, if you wish. 

All clips sped up 200%, audio down to 20%, no music. 

https://youtu.be/5VxnjwvlIMs



Now at 16 hours, all systems good, lots of power, leaps off the ground. 

Latest is various…

A panel hacksaw is a special type of saw for making long cuts in pieces of sheet metal. By using a piece of spring steel sheet to support the blade allows the saw to make unrestricted cuts.

A demonstration is made of trimming down a wing skin.

Flew my 601XL to Florida and back last week. What a great trip! The 601 and Corvair performed flawlessly. You can checkout the adventure on my blog: 2002 Mile Florida…

Funny thing – the original bungee on my 701 lasted for years. But with about 5 years and 200 hours on the aircraft, I was persuaded to replace it. So, I ordered one from Zenith, also the bungee replacement tool which helped - only to find the bungee was too big for my plane. It was really loose and with the gear off the ground, I could push the bungee off the pegs on the nose gear leg.

A quick call to Zenith, and Roger kindly digs up a smaller one and sends it to me. It fits…

First time poster, had a long road to airworthiness. Just wanted to let those of you with corvair engines know that the engine is very very hearty. This picture is from the first flight after I purchased the aircraft. The 2700 CC engine was overheated to the point where it melted the heads and gaskets. It landed pouring oil and smoking like a chimney. Running way too lean. It landed running though. Even with what is shown, the engine was chugging along. Now I have solved the issue, rebuilt…

Hey fellow Zenith builders: I am selling my CH701 and a potential buyer from out of state needs the plane modified to the wing fold option.  I do not have the facilities nor time any more to accomplish the work.  Would appreciate any info on where I can get this job done, preferably close to Oklahoma.  Don Herbel, Collinsville, Okla.

Here's my report of the 2019 Sun 'n Fun fly-in earlier this month (April 2 -  7) in Lakeland, Florida, with photos and videos of the trip to and from Lakeland from the…