thats a "701" :)

Im building a 791 with students and we are finally , after 7 summers, getting to the finishing touches.  I have no idea about paint prep, type, application etc.  any help out there?

jay

Here's a screen shot of the Zenith CH 750 Cruzer cabin as seen in QuickTime VR.

Download the high resolution Quicktime VR panoramic file to tour the Zenith CH 750 cabin in stunning high…

My 601XL has a 69" 48 pitch currently, with a C-0200 rated at

125 HP.  At 2300RPM I am just at 100MPH, I want to be at 115MPH

at 2100RPM (RPM X Pitch X .000947 = MPH), This would call for a 69" 58 pitch prop.

What are other Flyers out there using on 125HP engines for Dia. and Pitch?

Also is 115MPH cruse acceptable and safe.

This 601xl has the wing mod.

PS: Getting 125HP out of a 0200!!, 10-1 comp pistons,…

One of our pilots from Brazil is transitioning to the CH701 with the 912iS.  He put a GoPro on the mount and then created with You Tube video... https://www.youtube.com/watch?v=9ijgyJhgUic - although it is speeded up, it shows a lot of interesting hand movements in the cockpit... watch carefully as you see me in the right seat moving my hands around a lot!  Also check out the full and free movement prior to take off - as well as enjoy…

Plans indicate the trailing edge beveled edge on the top of the elevator pointing 15 degrees up, causing a permanent down trim.

The instructions indicate in two separate places, the beveled trailing edge should be on the bottom of the elevator creating a flat and  neutral lift trailing edge.

My question is:  which is the correct?

Solved some technical issues....so back on the air live.  Retired now so spending quite a few hours/week on this project.  Camera is currently focused on the seat area.  The channel is mostly for my kids/grandkids, but you're welcome to visit.     ustream.tv/channel/stevebetsy

Hi Builders,

I wanted to make very sure that my fuel senders were sealed before putting the tank in the wing and then filling it with fuel in the future!

The builders guide says the screws should have fiber washers under the head for sealing. These are no longer provided in the supplied VDO install kit. It sounds like a very good idea to have a fiber washer to help seal or a copper washer - like the seal washer used in banjo fuel fittings. I am also using the…

ICI en France,

Le club ULM "Bulles d'Air 51" à pris livraison de son ZENAIR 601 UL.

Avec un moteur Rotax 912S. La déco n'est pas encore finie.

Vitesse mini mesurée: 51 km/h  &  Maxi: 198 km/h !

Does anyone have a source for an aluminum airfoil shaped fairing that one could placed around front gear tube?

Preferably open at back so could be slipped around gear tube and then riveted shut and riveted to gear tube for stability.

Started the CH 750 wing build this weekend by conducting a first pass at form molds for the nose ribs and rear ribs, The center lightning hole on the rear rib is slightly off as that was my first attempt with the fly cutter. Will get some more lumber this week and try it again next weekend.

Trimmed and fitted forward dorsal piece to LE of horiz. stab.  For those that have done this, you know it takes a lot of small trimming and fitting.  The real artsy exercise is the aft piece which I have now completed.  It took considerably longer.  I plan on attaching these with nutplates and rivnuts instead of riveting.

701 builders: what trip value circuit breaker are you using to protect the nav light circuit of the Aeroflash dual (strobe, nav) light unit?  The units were supplied by Zenith as an option for my 701.  For a while during phase 1, I had a bad ground for the right wing nav light and could never tell during flight whether the light was working or not.  If I thumped the wingtip while in the hangar, the light would come on.  Aeroflash says the current draw for a 12V system should be 2 amps per…

After cutting the 59 mm hole for the fuel sender, I needed to get some chips out of the tank.

It worked well to get a small 110 VAC floodlight bulb and socket that would fit into the fuel cap hole to light the inside. To remove chips, taping a painters tack cloth to a long stick made it really easy to pick out random chips and make the tank inside clean and ready to seal the sender.

Larry Zepp - Zodiac 650B builder

You're invited to join us for our "Fly In To Summer" Builder Fly-In Gathering at the Zenith Aircraft Factory.…

 Hello, Im a new guy on the block, looking for any advice on a prop for a continental 0200A on my 750.  Any recommendations? Was told Warp Drive props were'nt too good......Thank you........Scott