0-200 Starter
Anyone have a skytec starter for the continental 0-200A that they would sellSee More
Zenith Aircraft Builders and Flyers
Online Community of Zenith Builders and Flyers
-
Thomas carlin
- Londonderry
- United Kingdom
- Blog Posts (1)
- Discussions (16)
- Events
- Groups
- Photos
- Photo Albums
- Videos
Thomas carlin's Discussions
0-200 Starter
Started Oct 23 0 Replies 0 Likes
Anyone have a skytec starter for the continental 0-200A that they would sellContinue
Wanted delco-remy starter clutch for an0-200
Started Oct 18 0 Replies 0 Likes
Hi Guys, Anyone have a delco-remy starter clutch on the old pull type starter fitted to the 0-200 attached a photo of the broken oneContinue
Crazed pilot strobes
Started this discussion. Last reply by Thomas carlin May 24. 8 Replies 0 Likes
Hi, Anyone fitted the crazed pilot strobes landing light etc with the controller controller ,wiring of the position lights are straight forward but I must be missing something as the installation…Continue
Slick Mags
Started this discussion. Last reply by Thomas carlin Feb 3. 2 Replies 0 Likes
Hi Guys, Reached the point in my CH750 plans build at which I fitted the S/H 0-200A. I had purchased the engine at the start of the project , it had been dry stored for a number years,…Continue
Thomas carlin's Page
Latest Activity
Wanted delco-remy starter clutch for an0-200
Hi Guys, Anyone have a delco-remy starter clutch on the old pull type starter fitted to the 0-200 attached a photo of the broken oneSee More
Crazed pilot strobes
Hi, Anyone fitted the crazed pilot strobes landing light etc with the controller controller ,wiring of the position lights are straight forward but I must be missing something as the installation diagram shows only a 12 v feed into the 2/3/4 ports on the green connector with a ground to no.1Any help appreciated See More
Slick Mags
Hi Guys, Reached the point in my CH750 plans build at which I fitted the S/H 0-200A. I had purchased the engine at the start of the project , it had been dry stored for a number years, being unable to get it running I traced the problem to a very weak spark from the magnetos,.Removed them for inspection and found that the coils & condensers were within specified limits and the points in ex condition, both had 200 HRS running time since the last inspection.The rotor magnets…See More
Propeller Wanted
Hi, I am looking for a 70 inch ground adjustable whirlwind propeller for my ch750 with a continental 0-200A engine.Regards, Tom Carlin See More
0-200A Alternator
Hi, Does anyone have any experience of the old continental 0-200A with I believe one of the first types of alternator, purchased the engine S/H from a 3rd party and it came with a type of rectifier I would associate with a dynamo rather than an alternator ,any help appreciated .Regards, Tom CarlinSee More
propeller for continental 0-200
Hi, Has anyone fitted a 68 DIA sensenich wood prop to the 750/ 0-200 combination,I know that zenith recommend 72/44 but in the U.K. the liscencing authority are unwilling at the moment to give approval for anything above 68 in.DIA. And would not give approve the Warp Drive I intended to fit stating problems with cracking in the hub area.Regards, Tom CarlinSee More
Fuesalage side cut outs
Hi,Cutting out the side window openings on my 750 but can't find any info in the drawings about the location of the banana shaped cut outs for the flaperon connections,can anyone help,Regards To AllTom CarlinSee More
Profile Information
- Aircraft Model
- STOL CH 750
- Project Status
- Less than half
- Building From
- Plans-only
- Engine installed (or plan to install)
- Continental O-200
- Building Experience
- No Experience
- Flying Experience
- Private Pilot
- Building and Flying Info / Your Profession / Other Background Info
- Retired engineer
- Home Airport (ie. KMYJ)
- Egl
Thomas carlin's Blog
Fuesalage side cut outs
Posted on August 5, 2020 at 7:18pm 6 Comments 0 Likes
Hi,
Cutting out the side window openings on my 750 but can't find any info in the drawings about the location of the banana shaped cut outs for the flaperon connections,can anyone help,
Regards To All
Tom Carlin
Cutting out the side window openings on my 750 but can't find any info in the drawings about the location of the banana shaped cut outs for the flaperon connections,can anyone help,
Regards To All
Tom Carlin
New from Zenith:
Classified listing for buying or selling your Zenith building or flying related stuff...
Custom Instrument Panels
for your Zenith:
Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, Dynon and Garmin avionics, and more.
Zenith Homecoming Tee:
Flying On Your Own Wings:
A Complete Guide to Understanding Light Airplane Design, by Chris Heintz
Builder & Pilot Supplies:
Pro Builder Assistance:
Transition training:
Aircraft Spruce & Specialty for all your building and pilot supplies!
How to videos from HomebuiltHELP.com
Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.
© 2024 Created by Zenith.Aero.
Powered by
Comment Wall
You need to be a member of Zenith Aircraft Builders and Flyers to add comments!
Join Zenith Aircraft Builders and Flyers